#bridge=br0
# Driver interface type (hostap/wired/madwifi/prism54/test/none/nl80211/bsd);
-# default: hostap)
+# default: hostap). nl80211 is used with all Linux mac80211 drivers.
# Use driver=none if building hostapd as a standalone RADIUS server that does
# not control any wireless/wired driver.
# driver=hostap
# SSID to be used in IEEE 802.11 management frames
ssid=test
-# Country code (ISO/IEC 3166-1). Used to set regulatory domain.
-# Modify as needed to indicate country in which device is operating.
+# Country code (ISO/IEC 3166-1). Used to set regulatory domain.
+# Set as needed to indicate country in which device is operating.
# This can limit available channels and transmit power.
-# (default: US)
#country_code=US
# Enable IEEE 802.11d. This advertises the country_code and the set of allowed
# 1 = enabled
#ieee80211n=1
+# ht_capab: HT capabilities (list of flags)
+# LDPC coding capability: [LDPC] = supported
+# Supported channel width set: [HT40-] = both 20 MHz and 40 MHz with secondary
+# channel below the primary channel; [HT40+] = both 20 MHz and 40 MHz
+# with secondary channel below the primary channel
+# (20 MHz only if neither is set)
+# Note: There are limits on which channels can be used with HT40- and
+# HT40+. Following table shows the channels that may be available for
+# HT40- and HT40+ use per IEEE 802.11n Annex J:
+# freq HT40- HT40+
+# 2.4 GHz 5-13 1-7 (1-9 in Europe/Japan)
+# 5 GHz 40,48,56,64 36,44,52,60
+# (depending on the location, not all of these channels may be available
+# for use)
+# Spatial Multiplexing (SM) Power Save: [SMPS-STATIC] or [SMPS-DYNAMIC]
+# (SMPS disabled if neither is set)
+# HT-greenfield: [GF] (disabled if not set)
+# Short GI for 20 MHz: [SHORT-GI-20] (disabled if not set)
+# Short GI for 40 MHz: [SHORT-GI-40] (disabled if not set)
+# Tx STBC: [TX-STBC] (disabled if not set)
+# Rx STBC: [RX-STBC1] (one spatial stream), [RX-STBC12] (one or two spatial
+# streams), or [RX-STBC123] (one, two, or three spatial streams); Rx STBC
+# disabled if none of these set
+# HT-delayed Block Ack: [DELAYED-BA] (disabled if not set)
+# Maximum A-MSDU length: [MAX-AMSDU-7935] for 7935 octets (3839 octets if not
+# set)
+# DSSS/CCK Mode in 40 MHz: [DSSS_CCK-40] = allowed (not allowed if not set)
+# PSMP support: [PSMP] (disabled if not set)
+# L-SIG TXOP protection support: [LSIG-TXOP-PROT] (disabled if not set)
+#ht_capab=[HT40-][SHORT-GI-20][SHORT-GI-40]
+
##### IEEE 802.1X-2004 related configuration ##################################
# Require IEEE 802.1X authorization
# 2 = required
#ieee80211w=0
-# Association ping timeout (in TU = 1.024 ms; for MFP)
-# dot11AssociationPingResponseTimeout, 1...4294967295
-#assoc_ping_timeout=1000
+# Association SA Query maximum timeout (in TU = 1.024 ms; for MFP)
+# (maximum time to wait for a SA Query response)
+# dot11AssociationSAQueryMaximumTimeout, 1...4294967295
+#assoc_sa_query_max_timeout=1000
-# Maximum number of association pings
-# dot11AssociationMaximumPingAttempts , 1...255
-#assoc_ping_attempts=3
+# Association SA Query retry timeout (in TU = 1.024 ms; for MFP)
+# (time between two subsequent SA Query requests)
+# dot11AssociationSAQueryRetryTimeout, 1...4294967295
+#assoc_sa_query_retry_timeout=201
# okc: Opportunistic Key Caching (aka Proactive Key Caching)
#ap_table_expiration_time=3600
+##### Wi-Fi Protected Setup (WPS) #############################################
+
+# WPS state
+# 0 = WPS disabled (default)
+# 1 = WPS enabled, not configured
+# 2 = WPS enabled, configured
+#wps_state=2
+
+# AP can be configured into a locked state where new WPS Registrar are not
+# accepted, but previously authorized Registrars (including the internal one)
+# can continue to add new Enrollees.
+#ap_setup_locked=1
+
+# Universally Unique IDentifier (UUID; see RFC 4122) of the device
+# This value is used as the UUID for the internal WPS Registrar. If the AP
+# is also using UPnP, this value should be set to the device's UPnP UUID.
+# If not configured, UUID will be generated based on the local MAC address.
+#uuid=12345678-9abc-def0-1234-56789abcdef0
+
+# Note: If wpa_psk_file is set, WPS is used to generate random, per-device PSKs
+# that will be appended to the wpa_psk_file. If wpa_psk_file is not set, the
+# default PSK (wpa_psk/wpa_passphrase) will be delivered to Enrollees. Use of
+# per-device PSKs is recommended as the more secure option (i.e., make sure to
+# set wpa_psk_file when using WPS with WPA-PSK).
+
+# When an Enrollee requests access to the network with PIN method, the Enrollee
+# PIN will need to be entered for the Registrar. PIN request notifications are
+# sent to hostapd ctrl_iface monitor. In addition, they can be written to a
+# text file that could be used, e.g., to populate the AP administration UI with
+# pending PIN requests. If the following variable is set, the PIN requests will
+# be written to the configured file.
+#wps_pin_requests=/var/run/hostapd_wps_pin_requests
+
+# Device Name
+# User-friendly description of device; up to 32 octets encoded in UTF-8
+#device_name=Wireless AP
+
+# Manufacturer
+# The manufacturer of the device (up to 64 ASCII characters)
+#manufacturer=Company
+
+# Model Name
+# Model of the device (up to 32 ASCII characters)
+#model_name=WAP
+
+# Model Number
+# Additional device description (up to 32 ASCII characters)
+#model_number=123
+
+# Serial Number
+# Serial number of the device (up to 32 characters)
+#serial_number=12345
+
+# Primary Device Type
+# Used format: <categ>-<OUI>-<subcateg>
+# categ = Category as an integer value
+# OUI = OUI and type octet as a 4-octet hex-encoded value; 0050F204 for
+# default WPS OUI
+# subcateg = OUI-specific Sub Category as an integer value
+# Examples:
+# 1-0050F204-1 (Computer / PC)
+# 1-0050F204-2 (Computer / Server)
+# 5-0050F204-1 (Storage / NAS)
+# 6-0050F204-1 (Network Infrastructure / AP)
+#device_type=6-0050F204-1
+
+# OS Version
+# 4-octet operating system version number (hex string)
+#os_version=01020300
+
+# Config Methods
+# List of the supported configuration methods
+#config_methods=label display push_button keypad
+
+# Access point PIN for initial configuration and adding Registrars
+# If not set, hostapd will not allow external WPS Registrars to control the
+# access point.
+#ap_pin=12345670
+
+# Skip building of automatic WPS credential
+# This can be used to allow the automatically generated Credential attribute to
+# be replaced with pre-configured Credential(s).
+#skip_cred_build=1
+
+# Additional Credential attribute(s)
+# This option can be used to add pre-configured Credential attributes into M8
+# message when acting as a Registrar. If skip_cred_build=1, this data will also
+# be able to override the Credential attribute that would have otherwise been
+# automatically generated based on network configuration. This configuration
+# option points to an external file that much contain the WPS Credential
+# attribute(s) as binary data.
+#extra_cred=hostapd.cred
+
+# Credential processing
+# 0 = process received credentials internally (default)
+# 1 = do not process received credentials; just pass them over ctrl_iface to
+# external program(s)
+# 2 = process received credentials internally and pass them over ctrl_iface
+# to external program(s)
+# Note: With wps_cred_processing=1, skip_cred_build should be set to 1 and
+# extra_cred be used to provide the Credential data for Enrollees.
+#
+# wps_cred_processing=1 will disabled automatic updates of hostapd.conf file
+# both for Credential processing and for marking AP Setup Locked based on
+# validation failures of AP PIN. An external program is responsible on updating
+# the configuration appropriately in this case.
+#wps_cred_processing=0
+
+# AP Settings Attributes for M7
+# By default, hostapd generates the AP Settings Attributes for M7 based on the
+# current configuration. It is possible to override this by providing a file
+# with pre-configured attributes. This is similar to extra_cred file format,
+# but the AP Settings attributes are not encapsulated in a Credential
+# attribute.
+#ap_settings=hostapd.ap_settings
+
+# WPS UPnP interface
+# If set, support for external Registrars is enabled.
+#upnp_iface=br0
+
+# Friendly Name (required for UPnP)
+# Short description for end use. Should be less than 64 characters.
+#friendly_name=WPS Access Point
+
+# Manufacturer URL (optional for UPnP)
+#manufacturer_url=http://www.example.com/
+
+# Model Description (recommended for UPnP)
+# Long description for end user. Should be less than 128 characters.
+#model_description=Wireless Access Point
+
+# Model URL (optional for UPnP)
+#model_url=http://www.example.com/model/
+
+# Universal Product Code (optional for UPnP)
+# 12-digit, all-numeric code that identifies the consumer package.
+#upc=123456789012
+
##### Multiple BSSID support ##################################################
#
# Above configuration is using the default interface (wlan#, or multi-SSID VLAN
projects / wpasupplicant / blobdiff