@itemize @minus
-@item
+@item
Full system emulation. In this mode, QEMU emulates a full system (for
example a PC), including one or several processors and various
peripherals. It can be used to launch different Operating Systems
without rebooting the PC or to debug system code.
-@item
+@item
User mode emulation. In this mode, QEMU can launch
processes compiled for one CPU on another CPU. It can be used to
launch the Wine Windows API emulator (@url{http://www.winehq.org}) or
@end itemize
QEMU can run without an host kernel driver and yet gives acceptable
-performance.
+performance.
For system emulation, the following hardware targets are supported:
@itemize
@item PC (x86 or x86_64 processor)
@item ISA PC (old style PC without PCI bus)
@item PREP (PowerPC processor)
-@item G3 BW PowerMac (PowerPC processor)
+@item G3 Beige PowerMac (PowerPC processor)
@item Mac99 PowerMac (PowerPC processor, in progress)
-@item Sun4m (32-bit Sparc processor)
-@item Sun4u (64-bit Sparc processor, in progress)
-@item Malta board (32-bit MIPS processor)
-@item ARM Integrator/CP (ARM926E, 1026E or 946E processor)
-@item ARM Versatile baseboard (ARM926E)
-@item ARM RealView Emulation baseboard (ARM926EJ-S)
-@item Spitz, Akita, Borzoi and Terrier PDAs (PXA270 processor)
+@item Sun4m/Sun4c/Sun4d (32-bit Sparc processor)
+@item Sun4u/Sun4v (64-bit Sparc processor, in progress)
+@item Malta board (32-bit and 64-bit MIPS processors)
+@item MIPS Magnum (64-bit MIPS processor)
+@item ARM Integrator/CP (ARM)
+@item ARM Versatile baseboard (ARM)
+@item ARM RealView Emulation baseboard (ARM)
+@item Spitz, Akita, Borzoi, Terrier and Tosa PDAs (PXA270 processor)
+@item Luminary Micro LM3S811EVB (ARM Cortex-M3)
+@item Luminary Micro LM3S6965EVB (ARM Cortex-M3)
@item Freescale MCF5208EVB (ColdFire V2).
@item Arnewsh MCF5206 evaluation board (ColdFire V2).
+@item Palm Tungsten|E PDA (OMAP310 processor)
+@item N800 and N810 tablets (OMAP2420 processor)
+@item MusicPal (MV88W8618 ARM processor)
+@item Gumstix "Connex" and "Verdex" motherboards (PXA255/270).
+@item Siemens SX1 smartphone (OMAP310 processor)
@end itemize
-For user emulation, x86, PowerPC, ARM, MIPS, Sparc32/64 and ColdFire(m68k) CPUs are supported.
+For user emulation, x86, PowerPC, ARM, 32-bit MIPS, Sparc32/64 and ColdFire(m68k) CPUs are supported.
@node Installation
@chapter Installation
* pcsys_network:: Network emulation
* direct_linux_boot:: Direct Linux Boot
* pcsys_usb:: USB emulation
+* vnc_security:: VNC security
* gdb_usage:: GDB usage
* pcsys_os_specific:: Target OS specific information
@end menu
following peripherals:
@itemize @minus
-@item
+@item
i440FX host PCI bridge and PIIX3 PCI to ISA bridge
@item
Cirrus CLGD 5446 PCI VGA card or dummy VGA card with Bochs VESA
extensions (hardware level, including all non standard modes).
@item
PS/2 mouse and keyboard
-@item
+@item
2 PCI IDE interfaces with hard disk and CD-ROM support
@item
Floppy disk
-@item
+@item
PCI/ISA PCI network adapters
@item
Serial ports
@item
ENSONIQ AudioPCI ES1370 sound card
@item
+Intel 82801AA AC97 Audio compatible sound card
+@item
Adlib(OPL2) - Yamaha YM3812 compatible chip
@item
+Gravis Ultrasound GF1 sound card
+@item
+CS4231A compatible sound card
+@item
PCI UHCI USB controller and a virtual USB hub.
@end itemize
SMP is supported with up to 255 CPUs.
-Note that adlib is only available when QEMU was configured with
--enable-adlib
+Note that adlib, gus and cs4231a are only available when QEMU was
+configured with --audio-card-list option containing the name(s) of
+required card(s).
QEMU uses the PC BIOS from the Bochs project and the Plex86/Bochs LGPL
VGA BIOS.
QEMU uses YM3812 emulation by Tatsuyuki Satoh.
+QEMU uses GUS emulation(GUSEMU32 @url{http://www.deinmeister.de/gusemu/})
+by Tibor "TS" Schütz.
+
+CS4231A is the chip used in Windows Sound System and GUSMAX products
+
@c man end
@node pcsys_quickstart
@example
@c man begin SYNOPSIS
-usage: qemu [options] [disk_image]
+usage: qemu [options] [@var{disk_image}]
@c man end
@end example
@c man begin OPTIONS
-@var{disk_image} is a raw hard disk image for IDE hard disk 0.
+@var{disk_image} is a raw hard disk image for IDE hard disk 0. Some
+targets do not need a disk image.
General options:
@table @option
-@item -M machine
-Select the emulated machine (@code{-M ?} for list)
+@item -h
+Display help and exit
+
+@item -M @var{machine}
+Select the emulated @var{machine} (@code{-M ?} for list)
-@item -fda file
-@item -fdb file
+@item -cpu @var{model}
+Select CPU model (-cpu ? for list and additional feature selection)
+
+@item -smp @var{n}
+Simulate an SMP system with @var{n} CPUs. On the PC target, up to 255
+CPUs are supported. On Sparc32 target, Linux limits the number of usable CPUs
+to 4.
+
+@item -fda @var{file}
+@item -fdb @var{file}
Use @var{file} as floppy disk 0/1 image (@pxref{disk_images}). You can
use the host floppy by using @file{/dev/fd0} as filename (@pxref{host_drives}).
-@item -hda file
-@item -hdb file
-@item -hdc file
-@item -hdd file
+@item -hda @var{file}
+@item -hdb @var{file}
+@item -hdc @var{file}
+@item -hdd @var{file}
Use @var{file} as hard disk 0, 1, 2 or 3 image (@pxref{disk_images}).
-@item -cdrom file
-Use @var{file} as CD-ROM image (you cannot use @option{-hdc} and and
+@item -cdrom @var{file}
+Use @var{file} as CD-ROM image (you cannot use @option{-hdc} and
@option{-cdrom} at the same time). You can use the host CD-ROM by
using @file{/dev/cdrom} as filename (@pxref{host_drives}).
-@item -boot [a|c|d|n]
-Boot on floppy (a), hard disk (c), CD-ROM (d), or Etherboot (n). Hard disk boot
-is the default.
+@item -drive @var{option}[,@var{option}[,@var{option}[,...]]]
-@item -snapshot
-Write to temporary files instead of disk image files. In this case,
-the raw disk image you use is not written back. You can however force
-the write back by pressing @key{C-a s} (@pxref{disk_images}).
+Define a new drive. Valid options are:
-@item -no-fd-bootchk
-Disable boot signature checking for floppy disks in Bochs BIOS. It may
-be needed to boot from old floppy disks.
+@table @code
+@item file=@var{file}
+This option defines which disk image (@pxref{disk_images}) to use with
+this drive. If the filename contains comma, you must double it
+(for instance, "file=my,,file" to use file "my,file").
+@item if=@var{interface}
+This option defines on which type on interface the drive is connected.
+Available types are: ide, scsi, sd, mtd, floppy, pflash, virtio.
+@item bus=@var{bus},unit=@var{unit}
+These options define where is connected the drive by defining the bus number and
+the unit id.
+@item index=@var{index}
+This option defines where is connected the drive by using an index in the list
+of available connectors of a given interface type.
+@item media=@var{media}
+This option defines the type of the media: disk or cdrom.
+@item cyls=@var{c},heads=@var{h},secs=@var{s}[,trans=@var{t}]
+These options have the same definition as they have in @option{-hdachs}.
+@item snapshot=@var{snapshot}
+@var{snapshot} is "on" or "off" and allows to enable snapshot for given drive (see @option{-snapshot}).
+@item cache=@var{cache}
+@var{cache} is "none", "writeback", or "writethrough" and controls how the host cache is used to access block data.
+@item format=@var{format}
+Specify which disk @var{format} will be used rather than detecting
+the format. Can be used to specifiy format=raw to avoid interpreting
+an untrusted format header.
+@item serial=@var{serial}
+This option specifies the serial number to assign to the device.
+@end table
-@item -m megs
-Set virtual RAM size to @var{megs} megabytes. Default is 128 MB.
+By default, writethrough caching is used for all block device. This means that
+the host page cache will be used to read and write data but write notification
+will be sent to the guest only when the data has been reported as written by
+the storage subsystem.
-@item -smp n
-Simulate an SMP system with @var{n} CPUs. On the PC target, up to 255
-CPUs are supported.
+Writeback caching will report data writes as completed as soon as the data is
+present in the host page cache. This is safe as long as you trust your host.
+If your host crashes or loses power, then the guest may experience data
+corruption. When using the @option{-snapshot} option, writeback caching is
+used by default.
-@item -nographic
+The host page can be avoided entirely with @option{cache=none}. This will
+attempt to do disk IO directly to the guests memory. QEMU may still perform
+an internal copy of the data.
-Normally, QEMU uses SDL to display the VGA output. With this option,
-you can totally disable graphical output so that QEMU is a simple
-command line application. The emulated serial port is redirected on
-the console. Therefore, you can still use QEMU to debug a Linux kernel
-with a serial console.
+Some block drivers perform badly with @option{cache=writethrough}, most notably,
+qcow2. If performance is more important than correctness,
+@option{cache=writeback} should be used with qcow2. By default, if no explicit
+caching is specified for a qcow2 disk image, @option{cache=writeback} will be
+used. For all other disk types, @option{cache=writethrough} is the default.
-@item -no-frame
+Instead of @option{-cdrom} you can use:
+@example
+qemu -drive file=file,index=2,media=cdrom
+@end example
-Do not use decorations for SDL windows and start them using the whole
-available screen space. This makes the using QEMU in a dedicated desktop
-workspace more convenient.
+Instead of @option{-hda}, @option{-hdb}, @option{-hdc}, @option{-hdd}, you can
+use:
+@example
+qemu -drive file=file,index=0,media=disk
+qemu -drive file=file,index=1,media=disk
+qemu -drive file=file,index=2,media=disk
+qemu -drive file=file,index=3,media=disk
+@end example
-@item -vnc display
+You can connect a CDROM to the slave of ide0:
+@example
+qemu -drive file=file,if=ide,index=1,media=cdrom
+@end example
-Normally, QEMU uses SDL to display the VGA output. With this option,
-you can have QEMU listen on VNC display @var{display} and redirect the VGA
-display over the VNC session. It is very useful to enable the usb
-tablet device when using this option (option @option{-usbdevice
-tablet}). When using the VNC display, you must use the @option{-k}
-option to set the keyboard layout if you are not using en-us.
+If you don't specify the "file=" argument, you define an empty drive:
+@example
+qemu -drive if=ide,index=1,media=cdrom
+@end example
+
+You can connect a SCSI disk with unit ID 6 on the bus #0:
+@example
+qemu -drive file=file,if=scsi,bus=0,unit=6
+@end example
-@var{display} may be in the form @var{interface:d}, in which case connections
-will only be allowed from @var{interface} on display @var{d}. Optionally,
-@var{interface} can be omitted. @var{display} can also be in the form
-@var{unix:path} where @var{path} is the location of a unix socket to listen for
-connections on.
+Instead of @option{-fda}, @option{-fdb}, you can use:
+@example
+qemu -drive file=file,index=0,if=floppy
+qemu -drive file=file,index=1,if=floppy
+@end example
+
+By default, @var{interface} is "ide" and @var{index} is automatically
+incremented:
+@example
+qemu -drive file=a -drive file=b"
+@end example
+is interpreted like:
+@example
+qemu -hda a -hdb b
+@end example
+@item -mtdblock file
+Use 'file' as on-board Flash memory image.
-@item -k language
+@item -sd file
+Use 'file' as SecureDigital card image.
+
+@item -pflash file
+Use 'file' as a parallel flash image.
+
+@item -boot [a|c|d|n]
+Boot on floppy (a), hard disk (c), CD-ROM (d), or Etherboot (n). Hard disk boot
+is the default.
+
+@item -snapshot
+Write to temporary files instead of disk image files. In this case,
+the raw disk image you use is not written back. You can however force
+the write back by pressing @key{C-a s} (@pxref{disk_images}).
+
+@item -m @var{megs}
+Set virtual RAM size to @var{megs} megabytes. Default is 128 MiB. Optionally,
+a suffix of ``M'' or ``G'' can be used to signify a value in megabytes or
+gigabytes respectively.
+
+@item -k @var{language}
Use keyboard layout @var{language} (for example @code{fr} for
French). This option is only needed where it is not easy to get raw PC
Will show the audio subsystem help: list of drivers, tunable
parameters.
-@item -soundhw card1,card2,... or -soundhw all
+@item -soundhw @var{card1}[,@var{card2},...] or -soundhw all
Enable audio and selected sound hardware. Use ? to print all
available sound hardware.
@example
-qemu -soundhw sb16,adlib hda
-qemu -soundhw es1370 hda
-qemu -soundhw all hda
+qemu -soundhw sb16,adlib disk.img
+qemu -soundhw es1370 disk.img
+qemu -soundhw ac97 disk.img
+qemu -soundhw all disk.img
qemu -soundhw ?
@end example
-@item -localtime
-Set the real time clock to local time (the default is to UTC
-time). This option is needed to have correct date in MS-DOS or
-Windows.
+Note that Linux's i810_audio OSS kernel (for AC97) module might
+require manually specifying clocking.
+
+@example
+modprobe i810_audio clocking=48000
+@end example
+
+@end table
+
+USB options:
+@table @option
+
+@item -usb
+Enable the USB driver (will be the default soon)
+
+@item -usbdevice @var{devname}
+Add the USB device @var{devname}. @xref{usb_devices}.
+
+@table @code
+
+@item mouse
+Virtual Mouse. This will override the PS/2 mouse emulation when activated.
+
+@item tablet
+Pointer device that uses absolute coordinates (like a touchscreen). This
+means qemu is able to report the mouse position without having to grab the
+mouse. Also overrides the PS/2 mouse emulation when activated.
+
+@item disk:[format=@var{format}]:file
+Mass storage device based on file. The optional @var{format} argument
+will be used rather than detecting the format. Can be used to specifiy
+format=raw to avoid interpreting an untrusted format header.
+
+@item host:bus.addr
+Pass through the host device identified by bus.addr (Linux only).
+
+@item host:vendor_id:product_id
+Pass through the host device identified by vendor_id:product_id (Linux only).
+
+@item serial:[vendorid=@var{vendor_id}][,productid=@var{product_id}]:@var{dev}
+Serial converter to host character device @var{dev}, see @code{-serial} for the
+available devices.
+
+@item braille
+Braille device. This will use BrlAPI to display the braille output on a real
+or fake device.
+
+@item net:options
+Network adapter that supports CDC ethernet and RNDIS protocols.
+
+@end table
+
+@item -name @var{name}
+Sets the @var{name} of the guest.
+This name will be displayed in the SDL window caption.
+The @var{name} will also be used for the VNC server.
+
+@item -uuid @var{uuid}
+Set system UUID.
+
+@end table
+
+Display options:
+@table @option
+
+@item -nographic
+
+Normally, QEMU uses SDL to display the VGA output. With this option,
+you can totally disable graphical output so that QEMU is a simple
+command line application. The emulated serial port is redirected on
+the console. Therefore, you can still use QEMU to debug a Linux kernel
+with a serial console.
+
+@item -curses
+
+Normally, QEMU uses SDL to display the VGA output. With this option,
+QEMU can display the VGA output when in text mode using a
+curses/ncurses interface. Nothing is displayed in graphical mode.
+
+@item -no-frame
+
+Do not use decorations for SDL windows and start them using the whole
+available screen space. This makes the using QEMU in a dedicated desktop
+workspace more convenient.
+
+@item -alt-grab
+
+Use Ctrl-Alt-Shift to grab mouse (instead of Ctrl-Alt).
+
+@item -no-quit
+
+Disable SDL window close capability.
+
+@item -sdl
+
+Enable SDL.
+
+@item -portrait
+
+Rotate graphical output 90 deg left (only PXA LCD).
+
+@item -vga @var{type}
+Select type of VGA card to emulate. Valid values for @var{type} are
+@table @code
+@item cirrus
+Cirrus Logic GD5446 Video card. All Windows versions starting from
+Windows 95 should recognize and use this graphic card. For optimal
+performances, use 16 bit color depth in the guest and the host OS.
+(This one is the default)
+@item std
+Standard VGA card with Bochs VBE extensions. If your guest OS
+supports the VESA 2.0 VBE extensions (e.g. Windows XP) and if you want
+to use high resolution modes (>= 1280x1024x16) then you should use
+this option.
+@item vmware
+VMWare SVGA-II compatible adapter. Use it if you have sufficiently
+recent XFree86/XOrg server or Windows guest with a driver for this
+card.
+@item none
+Disable VGA card.
+@end table
@item -full-screen
Start in full screen.
-@item -pidfile file
-Store the QEMU process PID in @var{file}. It is useful if you launch QEMU
-from a script.
+@item -vnc @var{display}[,@var{option}[,@var{option}[,...]]]
-@item -daemonize
-Daemonize the QEMU process after initialization. QEMU will not detach from
-standard IO until it is ready to receive connections on any of its devices.
-This option is a useful way for external programs to launch QEMU without having
-to cope with initialization race conditions.
+Normally, QEMU uses SDL to display the VGA output. With this option,
+you can have QEMU listen on VNC display @var{display} and redirect the VGA
+display over the VNC session. It is very useful to enable the usb
+tablet device when using this option (option @option{-usbdevice
+tablet}). When using the VNC display, you must use the @option{-k}
+parameter to set the keyboard layout if you are not using en-us. Valid
+syntax for the @var{display} is
-@item -win2k-hack
-Use it when installing Windows 2000 to avoid a disk full bug. After
-Windows 2000 is installed, you no longer need this option (this option
-slows down the IDE transfers).
+@table @code
+
+@item @var{host}:@var{d}
-@item -option-rom file
-Load the contents of file as an option ROM. This option is useful to load
-things like EtherBoot.
+TCP connections will only be allowed from @var{host} on display @var{d}.
+By convention the TCP port is 5900+@var{d}. Optionally, @var{host} can
+be omitted in which case the server will accept connections from any host.
+
+@item @code{unix}:@var{path}
+
+Connections will be allowed over UNIX domain sockets where @var{path} is the
+location of a unix socket to listen for connections on.
+
+@item none
-@item -name string
-Sets the name of the guest. This name will be display in the SDL window
-caption. The name will also be used for the VNC server.
+VNC is initialized but not started. The monitor @code{change} command
+can be used to later start the VNC server.
@end table
-USB options:
-@table @option
+Following the @var{display} value there may be one or more @var{option} flags
+separated by commas. Valid options are
-@item -usb
-Enable the USB driver (will be the default soon)
+@table @code
+
+@item reverse
+
+Connect to a listening VNC client via a ``reverse'' connection. The
+client is specified by the @var{display}. For reverse network
+connections (@var{host}:@var{d},@code{reverse}), the @var{d} argument
+is a TCP port number, not a display number.
+
+@item password
+
+Require that password based authentication is used for client connections.
+The password must be set separately using the @code{change} command in the
+@ref{pcsys_monitor}
+
+@item tls
+
+Require that client use TLS when communicating with the VNC server. This
+uses anonymous TLS credentials so is susceptible to a man-in-the-middle
+attack. It is recommended that this option be combined with either the
+@var{x509} or @var{x509verify} options.
+
+@item x509=@var{/path/to/certificate/dir}
+
+Valid if @option{tls} is specified. Require that x509 credentials are used
+for negotiating the TLS session. The server will send its x509 certificate
+to the client. It is recommended that a password be set on the VNC server
+to provide authentication of the client when this is used. The path following
+this option specifies where the x509 certificates are to be loaded from.
+See the @ref{vnc_security} section for details on generating certificates.
+
+@item x509verify=@var{/path/to/certificate/dir}
+
+Valid if @option{tls} is specified. Require that x509 credentials are used
+for negotiating the TLS session. The server will send its x509 certificate
+to the client, and request that the client send its own x509 certificate.
+The server will validate the client's certificate against the CA certificate,
+and reject clients when validation fails. If the certificate authority is
+trusted, this is a sufficient authentication mechanism. You may still wish
+to set a password on the VNC server as a second authentication layer. The
+path following this option specifies where the x509 certificates are to
+be loaded from. See the @ref{vnc_security} section for details on generating
+certificates.
+
+@item sasl
+
+Require that the client use SASL to authenticate with the VNC server.
+The exact choice of authentication method used is controlled from the
+system / user's SASL configuration file for the 'qemu' service. This
+is typically found in /etc/sasl2/qemu.conf. If running QEMU as an
+unprivileged user, an environment variable SASL_CONF_PATH can be used
+to make it search alternate locations for the service config.
+While some SASL auth methods can also provide data encryption (eg GSSAPI),
+it is recommended that SASL always be combined with the 'tls' and
+'x509' settings to enable use of SSL and server certificates. This
+ensures a data encryption preventing compromise of authentication
+credentials. See the @ref{vnc_security} section for details on using
+SASL authentication.
+
+@item acl
+
+Turn on access control lists for checking of the x509 client certificate
+and SASL party. For x509 certs, the ACL check is made against the
+certificate's distinguished name. This is something that looks like
+@code{C=GB,O=ACME,L=Boston,CN=bob}. For SASL party, the ACL check is
+made against the username, which depending on the SASL plugin, may
+include a realm component, eg @code{bob} or @code{bob@@EXAMPLE.COM}.
+When the @option{acl} flag is set, the initial access list will be
+empty, with a @code{deny} policy. Thus no one will be allowed to
+use the VNC server until the ACLs have been loaded. This can be
+achieved using the @code{acl} monitor command.
+
+@end table
-@item -usbdevice devname
-Add the USB device @var{devname}. @xref{usb_devices}.
@end table
Network options:
@table @option
-@item -net nic[,vlan=n][,macaddr=addr][,model=type]
+@item -net nic[,vlan=@var{n}][,macaddr=@var{addr}][,model=@var{type}][,name=@var{name}]
Create a new Network Interface Card and connect it to VLAN @var{n} (@var{n}
= 0 is the default). The NIC is an ne2k_pci by default on the PC
-target. Optionally, the MAC address can be changed. If no
+target. Optionally, the MAC address can be changed to @var{addr}
+and a @var{name} can be assigned for use in monitor commands. If no
@option{-net} option is specified, a single NIC is created.
Qemu can emulate several different models of network card.
Valid values for @var{type} are
@code{i82551}, @code{i82557b}, @code{i82559er},
@code{ne2k_pci}, @code{ne2k_isa}, @code{pcnet}, @code{rtl8139},
-@code{smc91c111}, @code{lance} and @code{mcf_fec}.
+@code{e1000}, @code{smc91c111}, @code{lance} and @code{mcf_fec}.
Not all devices are supported on all targets. Use -net nic,model=?
for a list of available devices for your target.
-@item -net user[,vlan=n][,hostname=name]
+@item -net user[,vlan=@var{n}][,hostname=@var{name}][,name=@var{name}]
Use the user mode network stack which requires no administrator
privilege to run. @option{hostname=name} can be used to specify the client
hostname reported by the builtin DHCP server.
-@item -net tap[,vlan=n][,fd=h][,ifname=name][,script=file]
-Connect the host TAP network interface @var{name} to VLAN @var{n} and
-use the network script @var{file} to configure it. The default
-network script is @file{/etc/qemu-ifup}. Use @option{script=no} to
-disable script execution. If @var{name} is not
-provided, the OS automatically provides one. @option{fd=h} can be
-used to specify the handle of an already opened host TAP interface. Example:
+@item -net channel,@var{port}:@var{dev}
+Forward @option{user} TCP connection to port @var{port} to character device @var{dev}
+
+@item -net tap[,vlan=@var{n}][,name=@var{name}][,fd=@var{h}][,ifname=@var{name}][,script=@var{file}][,downscript=@var{dfile}]
+Connect the host TAP network interface @var{name} to VLAN @var{n}, use
+the network script @var{file} to configure it and the network script
+@var{dfile} to deconfigure it. If @var{name} is not provided, the OS
+automatically provides one. @option{fd}=@var{h} can be used to specify
+the handle of an already opened host TAP interface. The default network
+configure script is @file{/etc/qemu-ifup} and the default network
+deconfigure script is @file{/etc/qemu-ifdown}. Use @option{script=no}
+or @option{downscript=no} to disable script execution. Example:
@example
qemu linux.img -net nic -net tap
@end example
-@item -net socket[,vlan=n][,fd=h][,listen=[host]:port][,connect=host:port]
+@item -net socket[,vlan=@var{n}][,name=@var{name}][,fd=@var{h}][,listen=[@var{host}]:@var{port}][,connect=@var{host}:@var{port}]
Connect the VLAN @var{n} to a remote VLAN in another QEMU virtual
machine using a TCP socket connection. If @option{listen} is
specified, QEMU waits for incoming connections on @var{port}
(@var{host} is optional). @option{connect} is used to connect to
-another QEMU instance using the @option{listen} option. @option{fd=h}
+another QEMU instance using the @option{listen} option. @option{fd}=@var{h}
specifies an already opened TCP socket.
Example:
-net socket,connect=127.0.0.1:1234
@end example
-@item -net socket[,vlan=n][,fd=h][,mcast=maddr:port]
+@item -net socket[,vlan=@var{n}][,name=@var{name}][,fd=@var{h}][,mcast=@var{maddr}:@var{port}]
Create a VLAN @var{n} shared with another QEMU virtual
-machines using a UDP multicast socket, effectively making a bus for
+machines using a UDP multicast socket, effectively making a bus for
every QEMU with same multicast address @var{maddr} and @var{port}.
NOTES:
@enumerate
-@item
-Several QEMU can be running on different hosts and share same bus (assuming
+@item
+Several QEMU can be running on different hosts and share same bus (assuming
correct multicast setup for these hosts).
@item
mcast support is compatible with User Mode Linux (argument @option{eth@var{N}=mcast}), see
/path/to/linux ubd0=/path/to/root_fs eth0=mcast
@end example
+@item -net vde[,vlan=@var{n}][,name=@var{name}][,sock=@var{socketpath}][,port=@var{n}][,group=@var{groupname}][,mode=@var{octalmode}]
+Connect VLAN @var{n} to PORT @var{n} of a vde switch running on host and
+listening for incoming connections on @var{socketpath}. Use GROUP @var{groupname}
+and MODE @var{octalmode} to change default ownership and permissions for
+communication port. This option is available only if QEMU has been compiled
+with vde support enabled.
+
+Example:
+@example
+# launch vde switch
+vde_switch -F -sock /tmp/myswitch
+# launch QEMU instance
+qemu linux.img -net nic -net vde,sock=/tmp/myswitch
+@end example
+
@item -net none
Indicate that no network devices should be configured. It is used to
override the default configuration (@option{-net nic -net user}) which
is activated if no @option{-net} options are provided.
-@item -tftp dir
+@item -tftp @var{dir}
When using the user mode network stack, activate a built-in TFTP
server. The files in @var{dir} will be exposed as the root of a TFTP server.
The TFTP client on the guest must be configured in binary mode (use the command
@code{bin} of the Unix TFTP client). The host IP address on the guest is as
usual 10.0.2.2.
-@item -bootp file
+@item -bootp @var{file}
When using the user mode network stack, broadcast @var{file} as the BOOTP
filename. In conjunction with @option{-tftp}, this can be used to network boot
a guest from a local directory.
qemu -hda linux.img -boot n -tftp /path/to/tftp/files -bootp /pxelinux.0
@end example
-@item -smb dir
+@item -smb @var{dir}
When using the user mode network stack, activate a built-in SMB
-server so that Windows OSes can access to the host files in @file{dir}
+server so that Windows OSes can access to the host files in @file{@var{dir}}
transparently.
In the guest Windows OS, the line:
must be added in the file @file{C:\WINDOWS\LMHOSTS} (for windows 9x/Me)
or @file{C:\WINNT\SYSTEM32\DRIVERS\ETC\LMHOSTS} (Windows NT/2000).
-Then @file{dir} can be accessed in @file{\\smbserver\qemu}.
+Then @file{@var{dir}} can be accessed in @file{\\smbserver\qemu}.
Note that a SAMBA server must be installed on the host OS in
@file{/usr/sbin/smbd}. QEMU was tested successfully with smbd version
2.2.7a from the Red Hat 9 and version 3.0.10-1.fc3 from Fedora Core 3.
-@item -redir [tcp|udp]:host-port:[guest-host]:guest-port
+@item -redir [tcp|udp]:@var{host-port}:[@var{guest-host}]:@var{guest-port}
When using the user mode network stack, redirect incoming TCP or UDP
connections to the host port @var{host-port} to the guest
@end table
+Bluetooth(R) options:
+@table @option
+
+@item -bt hci[...]
+Defines the function of the corresponding Bluetooth HCI. -bt options
+are matched with the HCIs present in the chosen machine type. For
+example when emulating a machine with only one HCI built into it, only
+the first @code{-bt hci[...]} option is valid and defines the HCI's
+logic. The Transport Layer is decided by the machine type. Currently
+the machines @code{n800} and @code{n810} have one HCI and all other
+machines have none.
+
+@anchor{bt-hcis}
+The following three types are recognized:
+
+@table @code
+@item -bt hci,null
+(default) The corresponding Bluetooth HCI assumes no internal logic
+and will not respond to any HCI commands or emit events.
+
+@item -bt hci,host[:@var{id}]
+(@code{bluez} only) The corresponding HCI passes commands / events
+to / from the physical HCI identified by the name @var{id} (default:
+@code{hci0}) on the computer running QEMU. Only available on @code{bluez}
+capable systems like Linux.
+
+@item -bt hci[,vlan=@var{n}]
+Add a virtual, standard HCI that will participate in the Bluetooth
+scatternet @var{n} (default @code{0}). Similarly to @option{-net}
+VLANs, devices inside a bluetooth network @var{n} can only communicate
+with other devices in the same network (scatternet).
+@end table
+
+@item -bt vhci[,vlan=@var{n}]
+(Linux-host only) Create a HCI in scatternet @var{n} (default 0) attached
+to the host bluetooth stack instead of to the emulated target. This
+allows the host and target machines to participate in a common scatternet
+and communicate. Requires the Linux @code{vhci} driver installed. Can
+be used as following:
+
+@example
+qemu [...OPTIONS...] -bt hci,vlan=5 -bt vhci,vlan=5
+@end example
+
+@item -bt device:@var{dev}[,vlan=@var{n}]
+Emulate a bluetooth device @var{dev} and place it in network @var{n}
+(default @code{0}). QEMU can only emulate one type of bluetooth devices
+currently:
+
+@table @code
+@item keyboard
+Virtual wireless keyboard implementing the HIDP bluetooth profile.
+@end table
+
+@end table
+
+i386 target only:
+
+@table @option
+
+@item -win2k-hack
+Use it when installing Windows 2000 to avoid a disk full bug. After
+Windows 2000 is installed, you no longer need this option (this option
+slows down the IDE transfers).
+
+@item -rtc-td-hack
+Use it if you experience time drift problem in Windows with ACPI HAL.
+This option will try to figure out how many timer interrupts were not
+processed by the Windows guest and will re-inject them.
+
+@item -no-fd-bootchk
+Disable boot signature checking for floppy disks in Bochs BIOS. It may
+be needed to boot from old floppy disks.
+
+@item -no-acpi
+Disable ACPI (Advanced Configuration and Power Interface) support. Use
+it if your guest OS complains about ACPI problems (PC target machine
+only).
+
+@item -no-hpet
+Disable HPET support.
+
+@item -acpitable [sig=@var{str}][,rev=@var{n}][,oem_id=@var{str}][,oem_table_id=@var{str}][,oem_rev=@var{n}] [,asl_compiler_id=@var{str}][,asl_compiler_rev=@var{n}][,data=@var{file1}[:@var{file2}]...]
+Add ACPI table with specified header fields and context from specified files.
+
+@end table
+
Linux boot specific: When using these options, you can use a given
Linux kernel without installing it in the disk image. It can be useful
for easier testing of various kernels.
@table @option
-@item -kernel bzImage
+@item -kernel @var{bzImage}
Use @var{bzImage} as kernel image.
-@item -append cmdline
+@item -append @var{cmdline}
Use @var{cmdline} as kernel command line
-@item -initrd file
+@item -initrd @var{file}
Use @var{file} as initial ram disk.
@end table
Debug/Expert options:
@table @option
-@item -serial dev
+@item -serial @var{dev}
Redirect the virtual serial port to host character device
@var{dev}. The default device is @code{vc} in graphical mode and
@code{stdio} in non graphical mode.
-This option can be used several times to simulate up to 4 serials
+This option can be used several times to simulate up to 4 serial
ports.
Use @code{-serial none} to disable all serial ports.
@item /dev/XXX
[Linux only] Use host tty, e.g. @file{/dev/ttyS0}. The host serial port
parameters are set according to the emulated ones.
-@item /dev/parportN
+@item /dev/parport@var{N}
[Linux only, parallel port only] Use host parallel port
@var{N}. Currently SPP and EPP parallel port features can be used.
-@item file:filename
-Write output to filename. No character can be read.
+@item file:@var{filename}
+Write output to @var{filename}. No character can be read.
@item stdio
[Unix only] standard input/output
-@item pipe:filename
+@item pipe:@var{filename}
name pipe @var{filename}
-@item COMn
+@item COM@var{n}
[Windows only] Use host serial port @var{n}
-@item udp:[remote_host]:remote_port[@@[src_ip]:src_port]
-This implements UDP Net Console. When @var{remote_host} or @var{src_ip} are not specified they default to @code{0.0.0.0}. When not using a specified @var{src_port} a random port is automatically chosen.
+@item udp:[@var{remote_host}]:@var{remote_port}[@@[@var{src_ip}]:@var{src_port}]
+This implements UDP Net Console.
+When @var{remote_host} or @var{src_ip} are not specified
+they default to @code{0.0.0.0}.
+When not using a specified @var{src_port} a random port is automatically chosen.
+@item msmouse
+Three button serial mouse. Configure the guest to use Microsoft protocol.
If you just want a simple readonly console you can use @code{netcat} or
@code{nc}, by starting qemu with: @code{-serial udp::4555} and nc as:
@end table
-@item tcp:[host]:port[,server][,nowait][,nodelay]
+@item tcp:[@var{host}]:@var{port}[,@var{server}][,nowait][,nodelay]
The TCP Net Console has two modes of operation. It can send the serial
I/O to a location or wait for a connection from a location. By default
the TCP Net Console is sent to @var{host} at the @var{port}. If you use
-serial tcp:192.168.0.100:4444,server,nowait
@end table
-@item telnet:host:port[,server][,nowait][,nodelay]
+@item telnet:@var{host}:@var{port}[,server][,nowait][,nodelay]
The telnet protocol is used instead of raw tcp sockets. The options
work the same as if you had specified @code{-serial tcp}. The
difference is that the port acts like a telnet server or client using
sequence. Typically in unix telnet you do it with Control-] and then
type "send break" followed by pressing the enter key.
-@item unix:path[,server][,nowait]
+@item unix:@var{path}[,server][,nowait]
A unix domain socket is used instead of a tcp socket. The option works the
same as if you had specified @code{-serial tcp} except the unix domain socket
@var{path} is used for connections.
-@item mon:dev_string
+@item mon:@var{dev_string}
This is a special option to allow the monitor to be multiplexed onto
another serial port. The monitor is accessed with key sequence of
@key{Control-a} and then pressing @key{c}. See monitor access
@item -serial mon:telnet::4444,server,nowait
@end table
+@item braille
+Braille device. This will use BrlAPI to display the braille output on a real
+or fake device.
+
@end table
-@item -parallel dev
+@item -parallel @var{dev}
Redirect the virtual parallel port to host device @var{dev} (same
devices as the serial port). On Linux hosts, @file{/dev/parportN} can
be used to use hardware devices connected on the corresponding host
Use @code{-parallel none} to disable all parallel ports.
-@item -monitor dev
+@item -monitor @var{dev}
Redirect the monitor to host device @var{dev} (same devices as the
serial port).
The default device is @code{vc} in graphical mode and @code{stdio} in
non graphical mode.
-@item -echr numeric_ascii_value
-Change the escape character used for switching to the monitor when using
-monitor and serial sharing. The default is @code{0x01} when using the
-@code{-nographic} option. @code{0x01} is equal to pressing
-@code{Control-a}. You can select a different character from the ascii
-control keys where 1 through 26 map to Control-a through Control-z. For
-instance you could use the either of the following to change the escape
-character to Control-t.
-@table @code
-@item -echr 0x14
-@item -echr 20
-@end table
+@item -pidfile @var{file}
+Store the QEMU process PID in @var{file}. It is useful if you launch QEMU
+from a script.
+
+@item -S
+Do not start CPU at startup (you must type 'c' in the monitor).
@item -s
-Wait gdb connection to port 1234 (@pxref{gdb_usage}).
-@item -p port
+Wait gdb connection to port 1234 (@pxref{gdb_usage}).
+
+@item -p @var{port}
Change gdb connection port. @var{port} can be either a decimal number
to specify a TCP port, or a host device (same devices as the serial port).
-@item -S
-Do not start CPU at startup (you must type 'c' in the monitor).
-@item -d
+
+@item -d
Output log in /tmp/qemu.log
-@item -hdachs c,h,s,[,t]
+@item -hdachs @var{c},@var{h},@var{s},[,@var{t}]
Force hard disk 0 physical geometry (1 <= @var{c} <= 16383, 1 <=
@var{h} <= 16, 1 <= @var{s} <= 63) and optionally force the BIOS
translation mode (@var{t}=none, lba or auto). Usually QEMU can guess
all those parameters. This option is useful for old MS-DOS disk
images.
-@item -L path
+@item -L @var{path}
Set the directory for the BIOS, VGA BIOS and keymaps.
-@item -std-vga
-Simulate a standard VGA card with Bochs VBE extensions (default is
-Cirrus Logic GD5446 PCI VGA). If your guest OS supports the VESA 2.0
-VBE extensions (e.g. Windows XP) and if you want to use high
-resolution modes (>= 1280x1024x16) then you should use this option.
+@item -bios @var{file}
+Set the filename for the BIOS.
-@item -no-acpi
-Disable ACPI (Advanced Configuration and Power Interface) support. Use
-it if your guest OS complains about ACPI problems (PC target machine
-only).
+@item -kernel-kqemu
+Enable KQEMU full virtualization (default is user mode only).
+
+@item -no-kqemu
+Disable KQEMU kernel module usage. KQEMU options are only available if
+KQEMU support is enabled when compiling.
+
+@item -enable-kvm
+Enable KVM full virtualization support. This option is only available
+if KVM support is enabled when compiling.
@item -no-reboot
Exit instead of rebooting.
-@item -loadvm file
+@item -no-shutdown
+Don't exit QEMU on guest shutdown, but instead only stop the emulation.
+This allows for instance switching to monitor to commit changes to the
+disk image.
+
+@item -loadvm @var{file}
Start right away with a saved state (@code{loadvm} in monitor)
-@item -semihosting
-Enable semihosting syscall emulation (ARM and M68K target machines only).
+@item -daemonize
+Daemonize the QEMU process after initialization. QEMU will not detach from
+standard IO until it is ready to receive connections on any of its devices.
+This option is a useful way for external programs to launch QEMU without having
+to cope with initialization race conditions.
-On ARM this implements the "Angel" interface.
-On M68K this implements the "ColdFire GDB" interface used by libgloss.
+@item -option-rom @var{file}
+Load the contents of @var{file} as an option ROM.
+This option is useful to load things like EtherBoot.
+
+@item -clock @var{method}
+Force the use of the given methods for timer alarm. To see what timers
+are available use -clock ?.
+
+@item -localtime
+Set the real time clock to local time (the default is to UTC
+time). This option is needed to have correct date in MS-DOS or
+Windows.
+
+@item -startdate @var{date}
+Set the initial date of the real time clock. Valid formats for
+@var{date} are: @code{now} or @code{2006-06-17T16:01:21} or
+@code{2006-06-17}. The default value is @code{now}.
+
+@item -icount [N|auto]
+Enable virtual instruction counter. The virtual cpu will execute one
+instruction every 2^N ns of virtual time. If @code{auto} is specified
+then the virtual cpu speed will be automatically adjusted to keep virtual
+time within a few seconds of real time.
+
+Note that while this option can give deterministic behavior, it does not
+provide cycle accurate emulation. Modern CPUs contain superscalar out of
+order cores with complex cache hierarchies. The number of instructions
+executed often has little or no correlation with actual performance.
+
+@item -echr numeric_ascii_value
+Change the escape character used for switching to the monitor when using
+monitor and serial sharing. The default is @code{0x01} when using the
+@code{-nographic} option. @code{0x01} is equal to pressing
+@code{Control-a}. You can select a different character from the ascii
+control keys where 1 through 26 map to Control-a through Control-z. For
+instance you could use the either of the following to change the escape
+character to Control-t.
+@table @code
+@item -echr 0x14
+@item -echr 20
+@end table
+
+@item -chroot dir
+Immediately before starting guest execution, chroot to the specified
+directory. Especially useful in combination with -runas.
+
+@item -runas user
+Immediately before starting guest execution, drop root privileges, switching
+to the specified user.
-Note that this allows guest direct access to the host filesystem,
-so should only be used with trusted guest OS.
@end table
@c man end
@table @key
@item Ctrl-a h
+@item Ctrl-a ?
Print this help
-@item Ctrl-a x
+@item Ctrl-a x
Exit emulator
-@item Ctrl-a s
+@item Ctrl-a s
Save disk data back to file (if -snapshot)
@item Ctrl-a t
-toggle console timestamps
+Toggle console timestamps
@item Ctrl-a b
Send break (magic sysrq in Linux)
@item Ctrl-a c
@item
Remove or insert removable media images
-(such as CD-ROM or floppies)
+(such as CD-ROM or floppies).
-@item
+@item
Freeze/unfreeze the Virtual Machine (VM) and save or restore its state
from a disk file.
@table @option
-@item help or ? [cmd]
+@item help or ? [@var{cmd}]
Show the help for all commands or just for command @var{cmd}.
-@item commit
-Commit changes to the disk images (if -snapshot is used)
+@item commit
+Commit changes to the disk images (if -snapshot is used).
-@item info subcommand
-show various information about the system state
+@item info @var{subcommand}
+Show various information about the system state.
@table @option
+@item info version
+show the version of QEMU
@item info network
show the various VLANs and the associated devices
+@item info chardev
+show the character devices
@item info block
show the block devices
+@item info block
+show block device statistics
@item info registers
show the cpu registers
+@item info cpus
+show infos for each CPU
@item info history
show the command line history
+@item info irq
+show the interrupts statistics (if available)
+@item info pic
+show i8259 (PIC) state
@item info pci
-show emulated PCI device
+show emulated PCI device info
+@item info tlb
+show virtual to physical memory mappings (i386 only)
+@item info mem
+show the active virtual memory mappings (i386 only)
+@item info hpet
+show state of HPET (i386 only)
+@item info kqemu
+show KQEMU information
+@item info kvm
+show KVM information
@item info usb
show USB devices plugged on the virtual USB hub
@item info usbhost
show all USB host devices
+@item info profile
+show profiling information
@item info capture
show information about active capturing
@item info snapshots
show list of VM snapshots
+@item info status
+show the current VM status (running|paused)
+@item info pcmcia
+show guest PCMCIA status
@item info mice
show which guest mouse is receiving events
+@item info vnc
+show the vnc server status
+@item info name
+show the current VM name
+@item info uuid
+show the current VM UUID
+@item info cpustats
+show CPU statistics
+@item info slirp
+show SLIRP statistics (if available)
+@item info migrate
+show migration status
+@item info balloon
+show balloon information
@end table
@item q or quit
Quit the emulator.
-@item eject [-f] device
+@item eject [-f] @var{device}
Eject a removable medium (use -f to force it).
-@item change device filename
-Change a removable medium.
+@item change @var{device} @var{setting}
-@item screendump filename
-Save screen into PPM image @var{filename}.
+Change the configuration of a device.
-@item mouse_move dx dy [dz]
-Move the active mouse to the specified coordinates @var{dx} @var{dy}
-with optional scroll axis @var{dz}.
+@table @option
+@item change @var{diskdevice} @var{filename} [@var{format}]
+Change the medium for a removable disk device to point to @var{filename}. eg
-@item mouse_button val
-Change the active mouse button state @var{val} (1=L, 2=M, 4=R).
+@example
+(qemu) change ide1-cd0 /path/to/some.iso
+@end example
+
+@var{format} is optional.
+
+@item change vnc @var{display},@var{options}
+Change the configuration of the VNC server. The valid syntax for @var{display}
+and @var{options} are described at @ref{sec_invocation}. eg
-@item mouse_set index
-Set which mouse device receives events at given @var{index}, index
-can be obtained with
@example
-info mice
+(qemu) change vnc localhost:1
@end example
-@item wavcapture filename [frequency [bits [channels]]]
-Capture audio into @var{filename}. Using sample rate @var{frequency}
-bits per sample @var{bits} and number of channels @var{channels}.
+@item change vnc password [@var{password}]
-Defaults:
-@itemize @minus
-@item Sample rate = 44100 Hz - CD quality
-@item Bits = 16
-@item Number of channels = 2 - Stereo
-@end itemize
+Change the password associated with the VNC server. If the new password is not
+supplied, the monitor will prompt for it to be entered. VNC passwords are only
+significant up to 8 letters. eg
-@item stopcapture index
-Stop capture with a given @var{index}, index can be obtained with
@example
-info capture
+(qemu) change vnc password
+Password: ********
@end example
-@item log item1[,...]
+@end table
+
+@item acl @var{subcommand} @var{aclname} @var{match} @var{index}
+
+Manage access control lists for network services. There are currently
+two named access control lists, @var{vnc.x509dname} and @var{vnc.username}
+matching on the x509 client certificate distinguished name, and SASL
+username respectively.
+
+@table @option
+@item acl show <aclname>
+list all the match rules in the access control list, and the default
+policy
+@item acl policy <aclname> @code{allow|deny}
+set the default access control list policy, used in the event that
+none of the explicit rules match. The default policy at startup is
+always @code{deny}
+@item acl allow <aclname> <match> [<index>]
+add a match to the access control list, allowing access. The match will
+normally be an exact username or x509 distinguished name, but can
+optionally include wildcard globs. eg @code{*@@EXAMPLE.COM} to allow
+all users in the @code{EXAMPLE.COM} kerberos realm. The match will
+normally be appended to the end of the ACL, but can be inserted
+earlier in the list if the optional @code{index} parameter is supplied.
+@item acl deny <aclname> <match> [<index>]
+add a match to the access control list, denying access. The match will
+normally be an exact username or x509 distinguished name, but can
+optionally include wildcard globs. eg @code{*@@EXAMPLE.COM} to allow
+all users in the @code{EXAMPLE.COM} kerberos realm. The match will
+normally be appended to the end of the ACL, but can be inserted
+earlier in the list if the optional @code{index} parameter is supplied.
+@item acl remove <aclname> <match>
+remove the specified match rule from the access control list.
+@item acl reset <aclname>
+remove all matches from the access control list, and set the default
+policy back to @code{deny}.
+@end table
+
+@item screendump @var{filename}
+Save screen into PPM image @var{filename}.
+
+@item logfile @var{filename}
+Output logs to @var{filename}.
+
+@item log @var{item1}[,...]
Activate logging of the specified items to @file{/tmp/qemu.log}.
-@item savevm [tag|id]
+@item savevm [@var{tag}|@var{id}]
Create a snapshot of the whole virtual machine. If @var{tag} is
provided, it is used as human readable identifier. If there is already
a snapshot with the same tag or ID, it is replaced. More info at
@ref{vm_snapshots}.
-@item loadvm tag|id
+@item loadvm @var{tag}|@var{id}
Set the whole virtual machine to the snapshot identified by the tag
@var{tag} or the unique snapshot ID @var{id}.
-@item delvm tag|id
+@item delvm @var{tag}|@var{id}
Delete the snapshot identified by @var{tag} or @var{id}.
@item stop
@item c or cont
Resume emulation.
-@item gdbserver [port]
-Start gdbserver session (default port=1234)
+@item gdbserver [@var{port}]
+Start gdbserver session (default @var{port}=1234)
-@item x/fmt addr
+@item x/fmt @var{addr}
Virtual memory dump starting at @var{addr}.
-@item xp /fmt addr
+@item xp /@var{fmt} @var{addr}
Physical memory dump starting at @var{addr}.
@var{fmt} is a format which tells the command how to format the
data. Its syntax is: @option{/@{count@}@{format@}@{size@}}
@table @var
-@item count
+@item count
is the number of items to be dumped.
@item format
@end table
-Examples:
+Examples:
@itemize
@item
Dump 10 instructions at the current instruction pointer:
-@example
+@example
(qemu) x/10i $eip
0x90107063: ret
0x90107064: sti
@item
Dump 80 16 bit values at the start of the video memory.
-@smallexample
+@smallexample
(qemu) xp/80hx 0xb8000
0x000b8000: 0x0b50 0x0b6c 0x0b65 0x0b78 0x0b38 0x0b36 0x0b2f 0x0b42
0x000b8010: 0x0b6f 0x0b63 0x0b68 0x0b73 0x0b20 0x0b56 0x0b47 0x0b41
@end smallexample
@end itemize
-@item p or print/fmt expr
+@item p or print/@var{fmt} @var{expr}
Print expression value. Only the @var{format} part of @var{fmt} is
used.
-@item sendkey keys
+@item sendkey @var{keys}
-Send @var{keys} to the emulator. Use @code{-} to press several keys
-simultaneously. Example:
+Send @var{keys} to the emulator. @var{keys} could be the name of the
+key or @code{#} followed by the raw value in either decimal or hexadecimal
+format. Use @code{-} to press several keys simultaneously. Example:
@example
sendkey ctrl-alt-f1
@end example
Reset the system.
-@item usb_add devname
+@item system_powerdown
+
+Power down the system (if supported).
+
+@item sum @var{addr} @var{size}
+
+Compute the checksum of a memory region.
+
+@item usb_add @var{devname}
Add the USB device @var{devname}. For details of available devices see
@ref{usb_devices}
-@item usb_del devname
+@item usb_del @var{devname}
Remove the USB device @var{devname} from the QEMU virtual USB
hub. @var{devname} has the syntax @code{bus.addr}. Use the monitor
command @code{info usb} to see the devices you can remove.
+@item mouse_move @var{dx} @var{dy} [@var{dz}]
+Move the active mouse to the specified coordinates @var{dx} @var{dy}
+with optional scroll axis @var{dz}.
+
+@item mouse_button @var{val}
+Change the active mouse button state @var{val} (1=L, 2=M, 4=R).
+
+@item mouse_set @var{index}
+Set which mouse device receives events at given @var{index}, index
+can be obtained with
+@example
+info mice
+@end example
+
+@item wavcapture @var{filename} [@var{frequency} [@var{bits} [@var{channels}]]]
+Capture audio into @var{filename}. Using sample rate @var{frequency}
+bits per sample @var{bits} and number of channels @var{channels}.
+
+Defaults:
+@itemize @minus
+@item Sample rate = 44100 Hz - CD quality
+@item Bits = 16
+@item Number of channels = 2 - Stereo
+@end itemize
+
+@item stopcapture @var{index}
+Stop capture with a given @var{index}, index can be obtained with
+@example
+info capture
+@end example
+
+@item memsave @var{addr} @var{size} @var{file}
+save to disk virtual memory dump starting at @var{addr} of size @var{size}.
+
+@item pmemsave @var{addr} @var{size} @var{file}
+save to disk physical memory dump starting at @var{addr} of size @var{size}.
+
+@item boot_set @var{bootdevicelist}
+
+Define new values for the boot device list. Those values will override
+the values specified on the command line through the @code{-boot} option.
+
+The values that can be specified here depend on the machine type, but are
+the same that can be specified in the @code{-boot} command line option.
+
+@item nmi @var{cpu}
+Inject an NMI on the given CPU.
+
+@item migrate [-d] @var{uri}
+Migrate to @var{uri} (using -d to not wait for completion).
+
+@item migrate_cancel
+Cancel the current VM migration.
+
+@item migrate_set_speed @var{value}
+Set maximum speed to @var{value} (in bytes) for migrations.
+
+@item balloon @var{value}
+Request VM to change its memory allocation to @var{value} (in MB).
+
+@item set_link @var{name} [up|down]
+Set link @var{name} up or down.
+
@end table
@subsection Integer expressions
* disk_images_snapshot_mode:: Snapshot mode
* vm_snapshots:: VM snapshots
* qemu_img_invocation:: qemu-img Invocation
+* qemu_nbd_invocation:: qemu-nbd Invocation
* host_drives:: Using host drives
* disk_images_fat_images:: Virtual FAT disk images
+* disk_images_nbd:: NBD access
@end menu
@node disk_images_quickstart
VM snapshots currently have the following known limitations:
@itemize
-@item
+@item
They cannot cope with removable devices if they are removed or
inserted after a snapshot is done.
-@item
+@item
A few device drivers still have incomplete snapshot support so their
state is not saved or restored properly (in particular USB).
@end itemize
@include qemu-img.texi
+@node qemu_nbd_invocation
+@subsection @code{qemu-nbd} Invocation
+
+@include qemu-nbd.texi
+
@node host_drives
@subsection Using host drives
is better to use the @code{change} or @code{eject} monitor commands to
change or eject media.
@item Hard disks
-Hard disks can be used with the syntax: @file{\\.\PhysicalDriveN}
+Hard disks can be used with the syntax: @file{\\.\PhysicalDrive@var{N}}
where @var{N} is the drive number (0 is the first hard disk).
WARNING: unless you know what you do, it is better to only make
@subsubsection Mac OS X
-@file{/dev/cdrom} is an alias to the first CDROM.
+@file{/dev/cdrom} is an alias to the first CDROM.
Currently there is no specific code to handle removable media, so it
is better to use the @code{change} or @code{eject} monitor commands to
QEMU can automatically create a virtual FAT disk image from a
directory tree. In order to use it, just type:
-@example
+@example
qemu linux.img -hdb fat:/my_directory
@end example
Floppies can be emulated with the @code{:floppy:} option:
-@example
+@example
qemu linux.img -fda fat:floppy:/my_directory
@end example
A read/write support is available for testing (beta stage) with the
@code{:rw:} option:
-@example
+@example
qemu linux.img -fda fat:floppy:rw:/my_directory
@end example
@item write to the FAT directory on the host system while accessing it with the guest system.
@end itemize
+@node disk_images_nbd
+@subsection NBD access
+
+QEMU can access directly to block device exported using the Network Block Device
+protocol.
+
+@example
+qemu linux.img -hdb nbd:my_nbd_server.mydomain.org:1024
+@end example
+
+If the NBD server is located on the same host, you can use an unix socket instead
+of an inet socket:
+
+@example
+qemu linux.img -hdb nbd:unix:/tmp/my_socket
+@end example
+
+In this case, the block device must be exported using qemu-nbd:
+
+@example
+qemu-nbd --socket=/tmp/my_socket my_disk.qcow2
+@end example
+
+The use of qemu-nbd allows to share a disk between several guests:
+@example
+qemu-nbd --socket=/tmp/my_socket --share=2 my_disk.qcow2
+@end example
+
+and then you can use it with two guests:
+@example
+qemu linux1.img -hdb nbd:unix:/tmp/my_socket
+qemu linux2.img -hdb nbd:unix:/tmp/my_socket
+@end example
+
@node pcsys_network
@section Network emulation
| (10.0.2.2)
|
----> DNS server (10.0.2.3)
- |
+ |
----> SMB server (10.0.2.4)
@end example
USB devices can be connected with the @option{-usbdevice} commandline option
or the @code{usb_add} monitor command. Available devices are:
-@table @var
-@item @code{mouse}
+@table @code
+@item mouse
Virtual Mouse. This will override the PS/2 mouse emulation when activated.
-@item @code{tablet}
+@item tablet
Pointer device that uses absolute coordinates (like a touchscreen).
This means qemu is able to report the mouse position without having
to grab the mouse. Also overrides the PS/2 mouse emulation when activated.
-@item @code{disk:file}
+@item disk:@var{file}
Mass storage device based on @var{file} (@pxref{disk_images})
-@item @code{host:bus.addr}
+@item host:@var{bus.addr}
Pass through the host device identified by @var{bus.addr}
(Linux only)
-@item @code{host:vendor_id:product_id}
+@item host:@var{vendor_id:product_id}
Pass through the host device identified by @var{vendor_id:product_id}
(Linux only)
-@item @code{wacom-tablet}
+@item wacom-tablet
Virtual Wacom PenPartner tablet. This device is similar to the @code{tablet}
above but it can be used with the tslib library because in addition to touch
coordinates it reports touch pressure.
-@item @code{keyboard}
+@item keyboard
Standard USB keyboard. Will override the PS/2 keyboard (if present).
+@item serial:[vendorid=@var{vendor_id}][,product_id=@var{product_id}]:@var{dev}
+Serial converter. This emulates an FTDI FT232BM chip connected to host character
+device @var{dev}. The available character devices are the same as for the
+@code{-serial} option. The @code{vendorid} and @code{productid} options can be
+used to override the default 0403:6001. For instance,
+@example
+usb_add serial:productid=FA00:tcp:192.168.0.2:4444
+@end example
+will connect to tcp port 4444 of ip 192.168.0.2, and plug that to the virtual
+serial converter, faking a Matrix Orbital LCD Display (USB ID 0403:FA00).
+@item braille
+Braille device. This will use BrlAPI to display the braille output on a real
+or fake device.
+@item net:@var{options}
+Network adapter that supports CDC ethernet and RNDIS protocols. @var{options}
+specifies NIC options as with @code{-net nic,}@var{options} (see description).
+For instance, user-mode networking can be used with
+@example
+qemu [...OPTIONS...] -net user,vlan=0 -usbdevice net:vlan=0
+@end example
+Currently this cannot be used in machines that support PCI NICs.
+@item bt[:@var{hci-type}]
+Bluetooth dongle whose type is specified in the same format as with
+the @option{-bt hci} option, @pxref{bt-hcis,,allowed HCI types}. If
+no type is given, the HCI logic corresponds to @code{-bt hci,vlan=0}.
+This USB device implements the USB Transport Layer of HCI. Example
+usage:
+@example
+qemu [...OPTIONS...] -usbdevice bt:hci,vlan=3 -bt device:keyboard,vlan=3
+@end example
@end table
@node host_usb_devices
Cameras) are not supported yet.
@enumerate
-@item If you use an early Linux 2.4 kernel, verify that no Linux driver
+@item If you use an early Linux 2.4 kernel, verify that no Linux driver
is actually using the USB device. A simple way to do that is simply to
disable the corresponding kernel module by renaming it from @file{mydriver.o}
to @file{mydriver.o.disabled}.
@end example
@item Launch QEMU and do in the monitor:
-@example
+@example
info usbhost
Device 1.2, speed 480 Mb/s
Class 00: USB device 1234:5678, USB DISK
hubs, it won't work).
@item Add the device in QEMU by using:
-@example
+@example
usb_add host:1234:5678
@end example
When relaunching QEMU, you may have to unplug and plug again the USB
device to make it work again (this is a bug).
+@node vnc_security
+@section VNC security
+
+The VNC server capability provides access to the graphical console
+of the guest VM across the network. This has a number of security
+considerations depending on the deployment scenarios.
+
+@menu
+* vnc_sec_none::
+* vnc_sec_password::
+* vnc_sec_certificate::
+* vnc_sec_certificate_verify::
+* vnc_sec_certificate_pw::
+* vnc_sec_sasl::
+* vnc_sec_certificate_sasl::
+* vnc_generate_cert::
+* vnc_setup_sasl::
+@end menu
+@node vnc_sec_none
+@subsection Without passwords
+
+The simplest VNC server setup does not include any form of authentication.
+For this setup it is recommended to restrict it to listen on a UNIX domain
+socket only. For example
+
+@example
+qemu [...OPTIONS...] -vnc unix:/home/joebloggs/.qemu-myvm-vnc
+@end example
+
+This ensures that only users on local box with read/write access to that
+path can access the VNC server. To securely access the VNC server from a
+remote machine, a combination of netcat+ssh can be used to provide a secure
+tunnel.
+
+@node vnc_sec_password
+@subsection With passwords
+
+The VNC protocol has limited support for password based authentication. Since
+the protocol limits passwords to 8 characters it should not be considered
+to provide high security. The password can be fairly easily brute-forced by
+a client making repeat connections. For this reason, a VNC server using password
+authentication should be restricted to only listen on the loopback interface
+or UNIX domain sockets. Password authentication is requested with the @code{password}
+option, and then once QEMU is running the password is set with the monitor. Until
+the monitor is used to set the password all clients will be rejected.
+
+@example
+qemu [...OPTIONS...] -vnc :1,password -monitor stdio
+(qemu) change vnc password
+Password: ********
+(qemu)
+@end example
+
+@node vnc_sec_certificate
+@subsection With x509 certificates
+
+The QEMU VNC server also implements the VeNCrypt extension allowing use of
+TLS for encryption of the session, and x509 certificates for authentication.
+The use of x509 certificates is strongly recommended, because TLS on its
+own is susceptible to man-in-the-middle attacks. Basic x509 certificate
+support provides a secure session, but no authentication. This allows any
+client to connect, and provides an encrypted session.
+
+@example
+qemu [...OPTIONS...] -vnc :1,tls,x509=/etc/pki/qemu -monitor stdio
+@end example
+
+In the above example @code{/etc/pki/qemu} should contain at least three files,
+@code{ca-cert.pem}, @code{server-cert.pem} and @code{server-key.pem}. Unprivileged
+users will want to use a private directory, for example @code{$HOME/.pki/qemu}.
+NB the @code{server-key.pem} file should be protected with file mode 0600 to
+only be readable by the user owning it.
+
+@node vnc_sec_certificate_verify
+@subsection With x509 certificates and client verification
+
+Certificates can also provide a means to authenticate the client connecting.
+The server will request that the client provide a certificate, which it will
+then validate against the CA certificate. This is a good choice if deploying
+in an environment with a private internal certificate authority.
+
+@example
+qemu [...OPTIONS...] -vnc :1,tls,x509verify=/etc/pki/qemu -monitor stdio
+@end example
+
+
+@node vnc_sec_certificate_pw
+@subsection With x509 certificates, client verification and passwords
+
+Finally, the previous method can be combined with VNC password authentication
+to provide two layers of authentication for clients.
+
+@example
+qemu [...OPTIONS...] -vnc :1,password,tls,x509verify=/etc/pki/qemu -monitor stdio
+(qemu) change vnc password
+Password: ********
+(qemu)
+@end example
+
+
+@node vnc_sec_sasl
+@subsection With SASL authentication
+
+The SASL authentication method is a VNC extension, that provides an
+easily extendable, pluggable authentication method. This allows for
+integration with a wide range of authentication mechanisms, such as
+PAM, GSSAPI/Kerberos, LDAP, SQL databases, one-time keys and more.
+The strength of the authentication depends on the exact mechanism
+configured. If the chosen mechanism also provides a SSF layer, then
+it will encrypt the datastream as well.
+
+Refer to the later docs on how to choose the exact SASL mechanism
+used for authentication, but assuming use of one supporting SSF,
+then QEMU can be launched with:
+
+@example
+qemu [...OPTIONS...] -vnc :1,sasl -monitor stdio
+@end example
+
+@node vnc_sec_certificate_sasl
+@subsection With x509 certificates and SASL authentication
+
+If the desired SASL authentication mechanism does not supported
+SSF layers, then it is strongly advised to run it in combination
+with TLS and x509 certificates. This provides securely encrypted
+data stream, avoiding risk of compromising of the security
+credentials. This can be enabled, by combining the 'sasl' option
+with the aforementioned TLS + x509 options:
+
+@example
+qemu [...OPTIONS...] -vnc :1,tls,x509,sasl -monitor stdio
+@end example
+
+
+@node vnc_generate_cert
+@subsection Generating certificates for VNC
+
+The GNU TLS packages provides a command called @code{certtool} which can
+be used to generate certificates and keys in PEM format. At a minimum it
+is neccessary to setup a certificate authority, and issue certificates to
+each server. If using certificates for authentication, then each client
+will also need to be issued a certificate. The recommendation is for the
+server to keep its certificates in either @code{/etc/pki/qemu} or for
+unprivileged users in @code{$HOME/.pki/qemu}.
+
+@menu
+* vnc_generate_ca::
+* vnc_generate_server::
+* vnc_generate_client::
+@end menu
+@node vnc_generate_ca
+@subsubsection Setup the Certificate Authority
+
+This step only needs to be performed once per organization / organizational
+unit. First the CA needs a private key. This key must be kept VERY secret
+and secure. If this key is compromised the entire trust chain of the certificates
+issued with it is lost.
+
+@example
+# certtool --generate-privkey > ca-key.pem
+@end example
+
+A CA needs to have a public certificate. For simplicity it can be a self-signed
+certificate, or one issue by a commercial certificate issuing authority. To
+generate a self-signed certificate requires one core piece of information, the
+name of the organization.
+
+@example
+# cat > ca.info <<EOF
+cn = Name of your organization
+ca
+cert_signing_key
+EOF
+# certtool --generate-self-signed \
+ --load-privkey ca-key.pem
+ --template ca.info \
+ --outfile ca-cert.pem
+@end example
+
+The @code{ca-cert.pem} file should be copied to all servers and clients wishing to utilize
+TLS support in the VNC server. The @code{ca-key.pem} must not be disclosed/copied at all.
+
+@node vnc_generate_server
+@subsubsection Issuing server certificates
+
+Each server (or host) needs to be issued with a key and certificate. When connecting
+the certificate is sent to the client which validates it against the CA certificate.
+The core piece of information for a server certificate is the hostname. This should
+be the fully qualified hostname that the client will connect with, since the client
+will typically also verify the hostname in the certificate. On the host holding the
+secure CA private key:
+
+@example
+# cat > server.info <<EOF
+organization = Name of your organization
+cn = server.foo.example.com
+tls_www_server
+encryption_key
+signing_key
+EOF
+# certtool --generate-privkey > server-key.pem
+# certtool --generate-certificate \
+ --load-ca-certificate ca-cert.pem \
+ --load-ca-privkey ca-key.pem \
+ --load-privkey server server-key.pem \
+ --template server.info \
+ --outfile server-cert.pem
+@end example
+
+The @code{server-key.pem} and @code{server-cert.pem} files should now be securely copied
+to the server for which they were generated. The @code{server-key.pem} is security
+sensitive and should be kept protected with file mode 0600 to prevent disclosure.
+
+@node vnc_generate_client
+@subsubsection Issuing client certificates
+
+If the QEMU VNC server is to use the @code{x509verify} option to validate client
+certificates as its authentication mechanism, each client also needs to be issued
+a certificate. The client certificate contains enough metadata to uniquely identify
+the client, typically organization, state, city, building, etc. On the host holding
+the secure CA private key:
+
+@example
+# cat > client.info <<EOF
+country = GB
+state = London
+locality = London
+organiazation = Name of your organization
+cn = client.foo.example.com
+tls_www_client
+encryption_key
+signing_key
+EOF
+# certtool --generate-privkey > client-key.pem
+# certtool --generate-certificate \
+ --load-ca-certificate ca-cert.pem \
+ --load-ca-privkey ca-key.pem \
+ --load-privkey client-key.pem \
+ --template client.info \
+ --outfile client-cert.pem
+@end example
+
+The @code{client-key.pem} and @code{client-cert.pem} files should now be securely
+copied to the client for which they were generated.
+
+
+@node vnc_setup_sasl
+
+@subsection Configuring SASL mechanisms
+
+The following documentation assumes use of the Cyrus SASL implementation on a
+Linux host, but the principals should apply to any other SASL impl. When SASL
+is enabled, the mechanism configuration will be loaded from system default
+SASL service config /etc/sasl2/qemu.conf. If running QEMU as an
+unprivileged user, an environment variable SASL_CONF_PATH can be used
+to make it search alternate locations for the service config.
+
+The default configuration might contain
+
+@example
+mech_list: digest-md5
+sasldb_path: /etc/qemu/passwd.db
+@end example
+
+This says to use the 'Digest MD5' mechanism, which is similar to the HTTP
+Digest-MD5 mechanism. The list of valid usernames & passwords is maintained
+in the /etc/qemu/passwd.db file, and can be updated using the saslpasswd2
+command. While this mechanism is easy to configure and use, it is not
+considered secure by modern standards, so only suitable for developers /
+ad-hoc testing.
+
+A more serious deployment might use Kerberos, which is done with the 'gssapi'
+mechanism
+
+@example
+mech_list: gssapi
+keytab: /etc/qemu/krb5.tab
+@end example
+
+For this to work the administrator of your KDC must generate a Kerberos
+principal for the server, with a name of 'qemu/somehost.example.com@@EXAMPLE.COM'
+replacing 'somehost.example.com' with the fully qualified host name of the
+machine running QEMU, and 'EXAMPLE.COM' with the Keberos Realm.
+
+Other configurations will be left as an exercise for the reader. It should
+be noted that only Digest-MD5 and GSSAPI provides a SSF layer for data
+encryption. For all other mechanisms, VNC should always be configured to
+use TLS and x509 certificates to protect security credentials from snooping.
+
@node gdb_usage
@section GDB usage
@code{x/10i $cs*16+$eip} to dump the code at the PC position.
@end enumerate
+Advanced debugging options:
+
+The default single stepping behavior is step with the IRQs and timer service routines off. It is set this way because when gdb executes a single step it expects to advance beyond the current instruction. With the IRQs and and timer service routines on, a single step might jump into the one of the interrupt or exception vectors instead of executing the current instruction. This means you may hit the same breakpoint a number of times before executing the instruction gdb wants to have executed. Because there are rare circumstances where you want to single step into an interrupt vector the behavior can be controlled from GDB. There are three commands you can query and set the single step behavior:
+@table @code
+@item maintenance packet qqemu.sstepbits
+
+This will display the MASK bits used to control the single stepping IE:
+@example
+(gdb) maintenance packet qqemu.sstepbits
+sending: "qqemu.sstepbits"
+received: "ENABLE=1,NOIRQ=2,NOTIMER=4"
+@end example
+@item maintenance packet qqemu.sstep
+
+This will display the current value of the mask used when single stepping IE:
+@example
+(gdb) maintenance packet qqemu.sstep
+sending: "qqemu.sstep"
+received: "0x7"
+@end example
+@item maintenance packet Qqemu.sstep=HEX_VALUE
+
+This will change the single step mask, so if wanted to enable IRQs on the single step, but not timers, you would use:
+@example
+(gdb) maintenance packet Qqemu.sstep=0x5
+sending: "qemu.sstep=0x5"
+received: "OK"
+@end example
+@end table
+
@node pcsys_os_specific
@section Target OS specific information
Add/Troubleshoot a device => Add a new device & Next => No, select the
hardware from a list & Next => NT Apm/Legacy Support & Next => Next
(again) a few times. Now the driver is installed and Windows 2000 now
-correctly instructs QEMU to shutdown at the appropriate moment.
+correctly instructs QEMU to shutdown at the appropriate moment.
@subsubsection Share a directory between Unix and Windows
QEMU emulates the following PowerMac peripherals:
@itemize @minus
-@item
-UniNorth PCI Bridge
+@item
+UniNorth or Grackle PCI Bridge
@item
PCI VGA compatible card with VESA Bochs Extensions
-@item
+@item
2 PMAC IDE interfaces with hard disk and CD-ROM support
-@item
+@item
NE2000 PCI adapters
@item
Non Volatile RAM
QEMU emulates the following PREP peripherals:
@itemize @minus
-@item
+@item
PCI Bridge
@item
PCI VGA compatible card with VESA Bochs Extensions
-@item
+@item
2 IDE interfaces with hard disk and CD-ROM support
@item
Floppy disk
-@item
+@item
NE2000 network adapters
@item
Serial port
QEMU uses the Open Hack'Ware Open Firmware Compatible BIOS available at
@url{http://perso.magic.fr/l_indien/OpenHackWare/index.htm}.
+Since version 0.9.1, QEMU uses OpenBIOS @url{http://www.openbios.org/}
+for the g3beige and mac99 PowerMac machines. OpenBIOS is a free (GPL
+v2) portable firmware implementation. The goal is to implement a 100%
+IEEE 1275-1994 (referred to as Open Firmware) compliant firmware.
+
@c man begin OPTIONS
The following options are specific to the PowerPC emulation:
@table @option
-@item -g WxH[xDEPTH]
+@item -g WxH[xDEPTH]
Set the initial VGA graphic mode. The default is 800x600x15.
+@item -prom-env string
+
+Set OpenBIOS variables in NVRAM, for example:
+
+@example
+qemu-system-ppc -prom-env 'auto-boot?=false' \
+ -prom-env 'boot-device=hd:2,\yaboot' \
+ -prom-env 'boot-args=conf=hd:2,\yaboot.conf'
+@end example
+
+These variables are not used by Open Hack'Ware.
+
@end table
-@c man end
+@c man end
More information is available at
@node Sparc32 System emulator
@section Sparc32 System emulator
-Use the executable @file{qemu-system-sparc} to simulate a SparcStation 5
-or SparcStation 10 (sun4m architecture). The emulation is somewhat complete.
+Use the executable @file{qemu-system-sparc} to simulate the following
+Sun4m architecture machines:
+@itemize @minus
+@item
+SPARCstation 4
+@item
+SPARCstation 5
+@item
+SPARCstation 10
+@item
+SPARCstation 20
+@item
+SPARCserver 600MP
+@item
+SPARCstation LX
+@item
+SPARCstation Voyager
+@item
+SPARCclassic
+@item
+SPARCbook
+@end itemize
+
+The emulation is somewhat complete. SMP up to 16 CPUs is supported,
+but Linux limits the number of usable CPUs to 4.
-QEMU emulates the following sun4m peripherals:
+It's also possible to simulate a SPARCstation 2 (sun4c architecture),
+SPARCserver 1000, or SPARCcenter 2000 (sun4d architecture), but these
+emulators are not usable yet.
+
+QEMU emulates the following sun4m/sun4c/sun4d peripherals:
@itemize @minus
@item
-IOMMU
+IOMMU or IO-UNITs
@item
TCX Frame buffer
-@item
+@item
Lance (Am7990) Ethernet
@item
-Non Volatile RAM M48T08
+Non Volatile RAM M48T02/M48T08
@item
Slave I/O: timers, interrupt controllers, Zilog serial ports, keyboard
and power/reset logic
@item
ESP SCSI controller with hard disk and CD-ROM support
@item
-Floppy drive
+Floppy drive (not on SS-600MP)
@item
CS4231 sound device (only on SS-5, not working yet)
@end itemize
-The number of peripherals is fixed in the architecture.
+The number of peripherals is fixed in the architecture. Maximum
+memory size depends on the machine type, for SS-5 it is 256MB and for
+others 2047MB.
Since version 0.8.2, QEMU uses OpenBIOS
@url{http://www.openbios.org/}. OpenBIOS is a free (GPL v2) portable
1275-1994 (referred to as Open Firmware) compliant firmware.
A sample Linux 2.6 series kernel and ram disk image are available on
-the QEMU web site. Please note that currently NetBSD, OpenBSD or
-Solaris kernels don't work.
+the QEMU web site. There are still issues with NetBSD and OpenBSD, but
+some kernel versions work. Please note that currently Solaris kernels
+don't work probably due to interface issues between OpenBIOS and
+Solaris.
@c man begin OPTIONS
-prom-env 'boot-device=sd(0,2,0):d' -prom-env 'boot-args=linux single'
@end example
-@item -M [SS-5|SS-10]
+@item -M [SS-4|SS-5|SS-10|SS-20|SS-600MP|LX|Voyager|SPARCClassic|SPARCbook|SS-2|SS-1000|SS-2000]
Set the emulated machine type. Default is SS-5.
@end table
-@c man end
+@c man end
@node Sparc64 System emulator
@section Sparc64 System emulator
-Use the executable @file{qemu-system-sparc64} to simulate a Sun4u machine.
-The emulator is not usable for anything yet.
+Use the executable @file{qemu-system-sparc64} to simulate a Sun4u
+(UltraSPARC PC-like machine), Sun4v (T1 PC-like machine), or generic
+Niagara (T1) machine. The emulator is not usable for anything yet, but
+it can launch some kernels.
-QEMU emulates the following sun4u peripherals:
+QEMU emulates the following peripherals:
@itemize @minus
@item
-UltraSparc IIi APB PCI Bridge
+UltraSparc IIi APB PCI Bridge
@item
PCI VGA compatible card with VESA Bochs Extensions
@item
+PS/2 mouse and keyboard
+@item
Non Volatile RAM M48T59
@item
PC-compatible serial ports
+@item
+2 PCI IDE interfaces with hard disk and CD-ROM support
+@item
+Floppy disk
@end itemize
+@c man begin OPTIONS
+
+The following options are specific to the Sparc64 emulation:
+
+@table @option
+
+@item -prom-env string
+
+Set OpenBIOS variables in NVRAM, for example:
+
+@example
+qemu-system-sparc64 -prom-env 'auto-boot?=false'
+@end example
+
+@item -M [sun4u|sun4v|Niagara]
+
+Set the emulated machine type. The default is sun4u.
+
+@end table
+
+@c man end
+
@node MIPS System emulator
@section MIPS System emulator
-Use the executable @file{qemu-system-mips} to simulate a MIPS machine.
-Three different machine types are emulated:
+Four executables cover simulation of 32 and 64-bit MIPS systems in
+both endian options, @file{qemu-system-mips}, @file{qemu-system-mipsel}
+@file{qemu-system-mips64} and @file{qemu-system-mips64el}.
+Five different machine types are emulated:
@itemize @minus
@item
@item
The MIPS Malta prototype board "malta"
@item
-An ACER Pica "pica61"
+An ACER Pica "pica61". This machine needs the 64-bit emulator.
+@item
+MIPS emulator pseudo board "mipssim"
+@item
+A MIPS Magnum R4000 machine "magnum". This machine needs the 64-bit emulator.
@end itemize
The generic emulation is supported by Debian 'Etch' and is able to
emulated:
@itemize @minus
-@item
-MIPS 24Kf CPU
+@item
+A range of MIPS CPUs, default is the 24Kf
@item
PC style serial port
@item
@item
Malta FPGA serial device
@item
-Cirrus VGA graphics card
+Cirrus (default) or any other PCI VGA graphics card
@end itemize
The ACER Pica emulation supports:
IDE controller
@end itemize
+The mipssim pseudo board emulation provides an environment similiar
+to what the proprietary MIPS emulator uses for running Linux.
+It supports:
+
+@itemize @minus
+@item
+A range of MIPS CPUs, default is the 24Kf
+@item
+PC style serial port
+@item
+MIPSnet network emulation
+@end itemize
+
+The MIPS Magnum R4000 emulation supports:
+
+@itemize @minus
+@item
+MIPS R4000 CPU
+@item
+PC-style IRQ controller
+@item
+PC Keyboard
+@item
+SCSI controller
+@item
+G364 framebuffer
+@end itemize
+
+
@node ARM System emulator
@section ARM System emulator
@itemize @minus
@item
-ARM926E, ARM1026E or ARM946E CPU
+ARM926E, ARM1026E, ARM946E, ARM1136 or Cortex-A8 CPU
@item
Two PL011 UARTs
-@item
+@item
SMC 91c111 Ethernet adapter
@item
PL110 LCD controller
@itemize @minus
@item
-ARM926E CPU
+ARM926E, ARM1136 or Cortex-A8 CPU
@item
PL190 Vectored Interrupt Controller
@item
Four PL011 UARTs
-@item
+@item
SMC 91c111 Ethernet adapter
@item
PL110 LCD controller
@itemize @minus
@item
-ARM926E CPU
+ARM926E, ARM1136, ARM11MPCORE(x4) or Cortex-A8 CPU
@item
ARM AMBA Generic/Distributed Interrupt Controller
@item
Four PL011 UARTs
-@item
+@item
SMC 91c111 Ethernet adapter
@item
PL110 LCD controller
WM8750 audio CODEC on I@math{^2}C and I@math{^2}S busses
@end itemize
+The Palm Tungsten|E PDA (codename "Cheetah") emulation includes the
+following elements:
+
+@itemize @minus
+@item
+Texas Instruments OMAP310 System-on-chip (ARM 925T core)
+@item
+ROM and RAM memories (ROM firmware image can be loaded with -option-rom)
+@item
+On-chip LCD controller
+@item
+On-chip Real Time Clock
+@item
+TI TSC2102i touchscreen controller / analog-digital converter / Audio
+CODEC, connected through MicroWire and I@math{^2}S busses
+@item
+GPIO-connected matrix keypad
+@item
+Secure Digital card connected to OMAP MMC/SD host
+@item
+Three on-chip UARTs
+@end itemize
+
+Nokia N800 and N810 internet tablets (known also as RX-34 and RX-44 / 48)
+emulation supports the following elements:
+
+@itemize @minus
+@item
+Texas Instruments OMAP2420 System-on-chip (ARM 1136 core)
+@item
+RAM and non-volatile OneNAND Flash memories
+@item
+Display connected to EPSON remote framebuffer chip and OMAP on-chip
+display controller and a LS041y3 MIPI DBI-C controller
+@item
+TI TSC2301 (in N800) and TI TSC2005 (in N810) touchscreen controllers
+driven through SPI bus
+@item
+National Semiconductor LM8323-controlled qwerty keyboard driven
+through I@math{^2}C bus
+@item
+Secure Digital card connected to OMAP MMC/SD host
+@item
+Three OMAP on-chip UARTs and on-chip STI debugging console
+@item
+A Bluetooth(R) transciever and HCI connected to an UART
+@item
+Mentor Graphics "Inventra" dual-role USB controller embedded in a TI
+TUSB6010 chip - only USB host mode is supported
+@item
+TI TMP105 temperature sensor driven through I@math{^2}C bus
+@item
+TI TWL92230C power management companion with an RTC on I@math{^2}C bus
+@item
+Nokia RETU and TAHVO multi-purpose chips with an RTC, connected
+through CBUS
+@end itemize
+
+The Luminary Micro Stellaris LM3S811EVB emulation includes the following
+devices:
+
+@itemize @minus
+@item
+Cortex-M3 CPU core.
+@item
+64k Flash and 8k SRAM.
+@item
+Timers, UARTs, ADC and I@math{^2}C interface.
+@item
+OSRAM Pictiva 96x16 OLED with SSD0303 controller on I@math{^2}C bus.
+@end itemize
+
+The Luminary Micro Stellaris LM3S6965EVB emulation includes the following
+devices:
+
+@itemize @minus
+@item
+Cortex-M3 CPU core.
+@item
+256k Flash and 64k SRAM.
+@item
+Timers, UARTs, ADC, I@math{^2}C and SSI interfaces.
+@item
+OSRAM Pictiva 128x64 OLED with SSD0323 controller connected via SSI.
+@end itemize
+
+The Freecom MusicPal internet radio emulation includes the following
+elements:
+
+@itemize @minus
+@item
+Marvell MV88W8618 ARM core.
+@item
+32 MB RAM, 256 KB SRAM, 8 MB flash.
+@item
+Up to 2 16550 UARTs
+@item
+MV88W8xx8 Ethernet controller
+@item
+MV88W8618 audio controller, WM8750 CODEC and mixer
+@item
+128×64 display with brightness control
+@item
+2 buttons, 2 navigation wheels with button function
+@end itemize
+
+The Siemens SX1 models v1 and v2 (default) basic emulation.
+The emulaton includes the following elements:
+
+@itemize @minus
+@item
+Texas Instruments OMAP310 System-on-chip (ARM 925T core)
+@item
+ROM and RAM memories (ROM firmware image can be loaded with -pflash)
+V1
+1 Flash of 16MB and 1 Flash of 8MB
+V2
+1 Flash of 32MB
+@item
+On-chip LCD controller
+@item
+On-chip Real Time Clock
+@item
+Secure Digital card connected to OMAP MMC/SD host
+@item
+Three on-chip UARTs
+@end itemize
+
A Linux 2.6 test image is available on the QEMU web site. More
information is available in the QEMU mailing-list archive.
+@c man begin OPTIONS
+
+The following options are specific to the ARM emulation:
+
+@table @option
+
+@item -semihosting
+Enable semihosting syscall emulation.
+
+On ARM this implements the "Angel" interface.
+
+Note that this allows guest direct access to the host filesystem,
+so should only be used with trusted guest OS.
+
+@end table
+
@node ColdFire System emulator
@section ColdFire System emulator
The M5208EVB emulation includes the following devices:
@itemize @minus
-@item
+@item
MCF5208 ColdFire V2 Microprocessor (ISA A+ with EMAC).
@item
Three Two on-chip UARTs.
The AN5206 emulation includes the following devices:
@itemize @minus
-@item
+@item
MCF5206 ColdFire V2 Microprocessor.
@item
Two on-chip UARTs.
@end itemize
-@node QEMU User space emulator
-@chapter QEMU User space emulator
+@c man begin OPTIONS
+
+The following options are specific to the ARM emulation:
+
+@table @option
+
+@item -semihosting
+Enable semihosting syscall emulation.
+
+On M68K this implements the "ColdFire GDB" interface used by libgloss.
+
+Note that this allows guest direct access to the host filesystem,
+so should only be used with trusted guest OS.
+
+@end table
+
+@node QEMU User space emulator
+@chapter QEMU User space emulator
@menu
* Supported Operating Systems ::
* Linux User space emulator::
* Mac OS X/Darwin User space emulator ::
+* BSD User space emulator ::
@end menu
@node Supported Operating Systems
Linux (referred as qemu-linux-user)
@item
Mac OS X/Darwin (referred as qemu-darwin-user)
+@item
+BSD (referred as qemu-bsd-user)
@end itemize
@node Linux User space emulator
@subsection Quick Start
In order to launch a Linux process, QEMU needs the process executable
-itself and all the target (x86) dynamic libraries used by it.
+itself and all the target (x86) dynamic libraries used by it.
@itemize
@item On x86, you can just try to launch any process by using the native
libraries:
-@example
+@example
qemu-i386 -L / /bin/ls
@end example
@item Since QEMU is also a linux process, you can launch qemu with
qemu (NOTE: you can only do that if you compiled QEMU from the sources):
-@example
+@example
qemu-i386 -L / qemu-i386 -L / /bin/ls
@end example
@code{LD_LIBRARY_PATH} is not set:
@example
-unset LD_LIBRARY_PATH
+unset LD_LIBRARY_PATH
@end example
Then you can launch the precompiled @file{ls} x86 executable:
@end example
@item Download the binary x86 Wine install
-(@file{qemu-XXX-i386-wine.tar.gz} on the QEMU web page).
+(@file{qemu-XXX-i386-wine.tar.gz} on the QEMU web page).
@item Configure Wine on your account. Look at the provided script
@file{/usr/local/qemu-i386/@/bin/wine-conf.sh}. Your previous
@subsection Command line options
@example
-usage: qemu-i386 [-h] [-d] [-L path] [-s size] program [arguments...]
+usage: qemu-i386 [-h] [-d] [-L path] [-s size] [-cpu model] [-g port] program [arguments...]
@end example
@table @option
@item -h
Print the help
-@item -L path
+@item -L path
Set the x86 elf interpreter prefix (default=/usr/local/qemu-i386)
@item -s size
Set the x86 stack size in bytes (default=524288)
+@item -cpu model
+Select CPU model (-cpu ? for list and additional feature selection)
@end table
Debug options:
Activate log (logfile=/tmp/qemu.log)
@item -p pagesize
Act as if the host page size was 'pagesize' bytes
+@item -g port
+Wait gdb connection to port
+@end table
+
+Environment variables:
+
+@table @env
+@item QEMU_STRACE
+Print system calls and arguments similar to the 'strace' program
+(NOTE: the actual 'strace' program will not work because the user
+space emulator hasn't implemented ptrace). At the moment this is
+incomplete. All system calls that don't have a specific argument
+format are printed with information for six arguments. Many
+flag-style arguments don't have decoders and will show up as numbers.
@end table
@node Other binaries
The binary format is detected automatically.
+@command{qemu-sparc} can execute Sparc32 binaries (Sparc32 CPU, 32 bit ABI).
+
+@command{qemu-sparc32plus} can execute Sparc32 and SPARC32PLUS binaries
+(Sparc64 CPU, 32 bit ABI).
+
+@command{qemu-sparc64} can execute some Sparc64 (Sparc64 CPU, 64 bit ABI) and
+SPARC32PLUS binaries (Sparc64 CPU, 32 bit ABI).
+
@node Mac OS X/Darwin User space emulator
@section Mac OS X/Darwin User space emulator
@item On x86, you can just try to launch any process by using the native
libraries:
-@example
+@example
qemu-i386 /bin/ls
@end example
or to run the ppc version of the executable:
-@example
+@example
qemu-ppc /bin/ls
@end example
@item On ppc, you'll have to tell qemu where your x86 libraries (and dynamic linker)
are installed:
-@example
+@example
qemu-i386 -L /opt/x86_root/ /bin/ls
@end example
@table @option
@item -h
Print the help
-@item -L path
+@item -L path
+Set the library root path (default=/)
+@item -s size
+Set the stack size in bytes (default=524288)
+@end table
+
+Debug options:
+
+@table @option
+@item -d
+Activate log (logfile=/tmp/qemu.log)
+@item -p pagesize
+Act as if the host page size was 'pagesize' bytes
+@end table
+
+@node BSD User space emulator
+@section BSD User space emulator
+
+@menu
+* BSD Status::
+* BSD Quick Start::
+* BSD Command line options::
+@end menu
+
+@node BSD Status
+@subsection BSD Status
+
+@itemize @minus
+@item
+target Sparc64 on Sparc64: Some trivial programs work.
+@end itemize
+
+@node BSD Quick Start
+@subsection Quick Start
+
+In order to launch a BSD process, QEMU needs the process executable
+itself and all the target dynamic libraries used by it.
+
+@itemize
+
+@item On Sparc64, you can just try to launch any process by using the native
+libraries:
+
+@example
+qemu-sparc64 /bin/ls
+@end example
+
+@end itemize
+
+@node BSD Command line options
+@subsection Command line options
+
+@example
+usage: qemu-sparc64 [-h] [-d] [-L path] [-s size] [-bsd type] program [arguments...]
+@end example
+
+@table @option
+@item -h
+Print the help
+@item -L path
Set the library root path (default=/)
@item -s size
Set the stack size in bytes (default=524288)
+@item -bsd type
+Set the type of the emulated BSD Operating system. Valid values are
+FreeBSD, NetBSD and OpenBSD (default).
@end table
Debug options:
@url{http://www.mingw.org/}. You can find detailed installation
instructions in the download section and the FAQ.
-@item Download
+@item Download
the MinGW development library of SDL 1.2.x
(@file{SDL-devel-1.2.x-@/mingw32.tar.gz}) from
@url{http://www.libsdl.org}. Unpack it in a temporary place, and
correct SDL directory when invoked.
@item Extract the current version of QEMU.
-
+
@item Start the MSYS shell (file @file{msys.bat}).
-@item Change to the QEMU directory. Launch @file{./configure} and
+@item Change to the QEMU directory. Launch @file{./configure} and
@file{make}. If you have problems using SDL, verify that
@file{sdl-config} can be launched from the MSYS command line.
-@item You can install QEMU in @file{Program Files/Qemu} by typing
+@item You can install QEMU in @file{Program Files/Qemu} by typing
@file{make install}. Don't forget to copy @file{SDL.dll} in
@file{Program Files/Qemu}.
Install the MinGW cross compilation tools available at
@url{http://www.mingw.org/}.
-@item
+@item
Install the Win32 version of SDL (@url{http://www.libsdl.org}) by
unpacking @file{i386-mingw32msvc.tar.gz}. Set up the PATH environment
variable so that @file{i386-mingw32msvc-sdl-config} can be launched by
the QEMU configuration script.
-@item
+@item
Configure QEMU for Windows cross compilation:
@example
./configure --enable-mingw32
chosen for the MinGW tools with --cross-prefix. You can also use
--prefix to set the Win32 install path.
-@item You can install QEMU in the installation directory by typing
+@item You can install QEMU in the installation directory by typing
@file{make install}. Don't forget to copy @file{SDL.dll} in the
-installation directory.
+installation directory.
@end itemize
projects / qemu / blobdiff